International EMC standard list Part-5

raoul_yang

  Other Standards

AE4L-81-2:1989—Test waveforms and techniques for assessing the effects of lightning-induced transients.

AIR 1147A:1970—Electromagnetic interference on aircraft from jet engine charging.

AIR 1209:1998—Construction and calibration of parallel plate transmission line for electromagnetic interference susceptibility testing.

AIR 1221:1971—Electromagnetic compatibility (EMC) system design checklist.

AIR 1255:1971—Spectrum analyzers for electromagnetic interference measurements.

AIR 1394:1998—Cabling guidelines for electromagnetic compatibility.

AIR 1404:1976—Dc resistivity versus RF impedance of EMI gaskets.

AIR 1423:1977—Electromagnetic compatibility on gas turbine engines for aircraft propulsion.

AIR 1425:1998—Methods of achieving electromagnetic compatibility of gas turbine engine accessories, for self-propelled vehicles.

AIR 1700:1998—Upper frequency measurement boundary for evaluation of shielding effectiveness in cylindrical systems.

ANSI C37.32:2002—American national standard for switchgear—High-voltage air switches, bus supports, and switch accessories—Schedules of preferred ratings, manufacturing specifications, and application guide.

ANSI C37.42:1996—American national standard for switchgear—Distribution cutouts and fuse links—Specifications.

ANSI C37.44:1981 (R1992)—American national standard specifications for distribution oil cutouts and fuse links.

ANSI C37.45:1981 (R1992)—American national standard specifications for distribution enclosed single-pole air switches.

ANSI C37.50:1989—American national standard for switchgear—Low-voltage ac power circuit breakers used in enclosures—Test procedures.

ANSI C37.51:1989—American national standard for switchgear—Metal-enclosed low-voltage ac power circuit-breaker switchgear assemblies—Conformance test procedures.

ANSI C37.52:2000—American national standard test procedures for low-voltage ac power circuit protectors used in enclosures.

ANSI C37.54:2002—American national standard for switchgear—Indoor alternating-current high-voltage circuit breakers applied as removable elements in metal-enclosed switchgear assemblies—Conformance test procedures.

ANSI C37.55:2002—American national standard for switchgear—Metal-clad switchgear assemblies—Conformance test procedures.

ANSI C37.57:1990—American national standard for switchgear—Metal-enclosed interrupter switchgear assemblies—Conformance testing.

ANSI C37.58:1990—American national standard for switchgear—Indoor ac medium-voltage switches for use in metal-enclosed switchgear—Conformance test procedures.

ANSI C37.66:1969 (R1997)—American national standard for requirements for oil-filled capacitor switches for alternating-current systems.

ANSI C37.85:2002—American national standard for switchgear—Alternating-current high-voltage power vacuum interrupters—Safety requirements for x-radiation limits.

AS 8023:1985—Airborne static electric power inverters.

AS 13441:1998—Test methods for electrical connectors.

AS 25064:1999—Conduit, flexible, radio-frequency shielding.

ASTM B904:2000—Standard specification for autocatalytic nickel over autocatalytic copper for electromagnetic interference shielding.

ASTM E1004:2002—Electrical conductivity, using the electromagnetic (eddy current) method, determining.

IEEE 32:1972 (R1997)—IEEE standard requirements, terminology, and test procedures for neutral grounding devices.

IEEE 81:1983—Guide for measuring earth resistivity, ground impedance, and earth surface potentials of a ground system.

IEEE 139:1988 (R1999)—IEEE recommended practice for the measurement of radio-frequency emission from industrial, scientific, and medical (ISM) equipment installed on user's premises.

IEEE 140:1990 (R1995)—IEEE recommended practice for minimization of interference from radio-frequency heating equipment.

IEEE 213:1987 (R1998)—IEEE standard procedure for measuring conducted emissions in the range of 300 kHz to 25 MHz from television and FM broadcast receivers to power lines.

IEEE 291:1991—IEEE standard methods for measuring electromagnetic field strength of sinusoidal continuous waves, 30 Hz to 30 GHz.

IEEE 299:1997—IEEE standard for measuring the effectiveness of the electromagnetic shielding enclosure.

IEEE 376:1974 (R1998)—IEEE standard for the measurement of impulse strength and impulse bandwidth.

IEEE 469:1988 (R1994)—IEEE recommended practice for voice-frequency electrical-noise tests of distribution transformers.

IEEE 473:1985 (R1997)—IEEE recommended practice for an electromagnetic site survey (10 kHz to 10 GHz).

IEEE 475:2000—IEEE standard measurement procedure for field-disturbance sensors, 300 MHz to 40 GHz.

IEEE 518:1982 (R1996)—IEEE guide for the installation of electrical equipment to minimize noise inputs to controllers from external sources.

IEEE 539:1990—IEEE standard definitions of terms relating to corona and field effects of overhead power lines.

IEEE 644:1994 (R2001)—IEEE standard procedure for measurement of power frequency electric and magnetic fields from ac power lines.

IEEE 776:1992 (R1998)—IEEE recommended practice for inductive coordination of electric supply and communication lines.

IEEE 824:1994—IEEE standard for series capacitors in power systems.

IEEE 935:1989 (R2001)—IEEE guide on terminology for tools and equipment to be used in live-line working (IEC 743:1983).

IEEE 1036:1992—IEEE guide for application of shunt power capacitors.

IEEE 1048:1990—IEEE guide for protective grounding of power lines.

IEEE 1128:1998—IEEE recommended practice for radio-frequency (RF) absorber evaluation in the range of 30 MHz to 5 GHz.

IEEE 1140:1994 (R1999)—IEEE standard test procedures for the measurement of electric and magnetic fields from video display terminals (VDTs) from 5 Hz to 400 kHz.

IEEE 1247:1998—IEEE standard for interrupter switches for ac, rated above 1000 V.

IEEE 1302:1998—IEEE guide for the electromagnetic characterization of conductive gaskets in the frequency range of dc to 18 GHz (references IEEE 100:1996 and 299:1997).

IEEE 1309:1996—IEEE standard for calibration of electromagnetic field sensors and probes excluding antennas from 9 kHz to 40 GHz.

IEEE 1460:1996—IEEE guide for the measurement of quasi-static magnetic and electric fields.

IEEE C37.04:1999—IEEE standard rating structure for ac high-voltage circuit breakers.

IEEE C37.09:1999—IEEE standard test procedure for ac high-voltage circuit breakers rated on a symmetrical current basis.

IEEE C37.010:1999—IEEE application guide for ac high-voltage circuit breakers rated on a symmetrical current basis.

IEEE C37.012:1979 (R2000)—IEEE application guide for capacitance current switching for ac high-voltage circuit breakers rated on a symmetrical current basis.

IEEE C37.083:1999—IEEE guide to synthetic capacitive current-switching test of ac high-voltage circuit breakers.

IEEE C37.14:2002—IEEE standard for low-voltage dc power circuit breakers used in enclosures.

IEEE C37.24:1986 (R1998)—IEEE guide for evaluating the effect of solar radiation on outdoor metal-enclosed switchgear.

IEEE C37.26:1972 (R1996)—IEEE standard guide for methods of power-factor measurement for low-voltage inductive test circuits.

IEEE C37.27:1987 (R1998)—IEEE standard application guide for low-voltage ac nonintegrally fused power circuit breakers (using separately mounted current-limiting fuses).

IEEE C37.29:1981 (R1990)—IEEE standard for low-voltage ac power circuit protectors used in enclosures.

IEEE C37.30:1997—IEEE standard requirements for high-voltage switches.

IEEE C37.34:1994—IEEE standard test code for high-voltage air switches.

IEEE C37.35:1995—IEEE guide for the application, installation, operation, and maintenance of high-voltage air disconnecting and load interrupter switches.

IEEE C37.36B:1990—IEEE guide to current interruption with horn-gap air switches.

IEEE C37.37:1996—IEEE standard for loading guide for ac high-voltage air switches (in excess of 1000 V).

IEEE C37.38:1989—IEEE standard for gas-insulated, metal-enclosed disconnecting, interrupter, and grounding switches.

IEEE C37.40:1993—IEEE standard service conditions and definitions for high-voltage fuses, distribution enclosed single-pole air switches, fuse disconnecting switches, and accessories.

IEEE C37.40B:1996—IEEE standard service conditions and definitions for external fuses for shunt capacitors.

IEEE C37.41:2000—IEEE standard design tests for high-voltage fuses, distribution enclosed single-pole air switches, fuse disconnecting switches, and accessories.

IEEE C37.41E:1996—IEEE standard design tests for external fuses and shunt capacitors.

IEEE C37.48:1997—IEEE guide for application, operation, and maintenance of high-voltage fuses, distribution enclosed single-pole air switches, fuse disconnecting switches, and accessories.

IEEE C37.59:2002—IEEE standard requirements for conversion of power switchgear equipment.

IEEE C37.60:1981 (R1992)—IEEE standard requirements for overhead, pad-mounted, dry-vault, and submersible automatic circuit reclosers and fault interrupters for ac systems.

IEEE C37.61:1973 (R1992)—IEEE standard guide for the application, operation, and maintenance of automatic circuit reclosers.

IEEE C37.63:1997—IEEE standard requirements for overhead, pad-mounted, dry-vault, and submersible automatic line sectionalizers of ac systems (references: IEEE 4:1995, 386:1995, C37.09:1979 [R1988], C37.24:1986 [R1991], C37.100:1992).

IEEE C37.71:2001—IEEE standard for three-phase, manually operated subsurface load interrupting switches for alternating current systems.

IEEE C37.81:1989 (R1999)—IEEE guide for seismic qualification of Class 1E metal-enclosed power switchgear assemblies.

IEEE C37.90.2:1995 (R2001)—IEEE standard withstand capability of relay systems to radiated electromagnetic interference from transceivers.

IEEE C37.99:2000—IEEE guide for the protection of shunt capacitor banks.

IEEE C37.100:1992—IEEE standard definitions for power switchgear.

IEEE C63.011:2000—Limits and methods of measurement of radio disturbance characteristics of industrial, scientific, and medical (ISM) radio-frequency equipment.

IEEE C63.022:1996—Limits and methods of measurement of radio disturbance characteristics of information technology equipment.

IEEE C63.2:1996—Electromagnetic noise and field strength instrumentation, 10 kHz to 40 GHz specifications.

IEEE C63.4:2000—Methods of measurement of radio-noise emissions from low-voltage electrical and electronic equipment in the range of 9 kHz to 40 GHz.

IEEE C63.5:1998—Electromagnetic compatibility—Radiated emission measurements in electromagnetic interference (EMI) control—Calibration of antennas.

IEEE C63.6:1996—Guide for the computation of errors in open-area test site measurements.

IEEE C63.7:1992—Construction of open-area test sites for performing radiated emission measurements.

IEEE C63.12:1999—Recommended practice for electromagnetic compatibility limits.

IEEE C63.13:1991—Guide on the application and evaluation of EMI power-line filters for commercial use.

IEEE C63.14:1998—Dictionary for technologies of electromagnetic compatibility (EMC), electromagnetic pulse (EMP), and electrostatic discharge (ESD).

IEEE C63.17:1998—Methods of measurement of the electromagnetic and operational compatibility of unlicensed personal communications services (UPCS) devices.

IEEE C63.18:1997—Recommended practice for an on-site ad hoc test method for estimating radiated electromagnetic immunity of medical devices to specific radio-frequency transmitters.

IEEE C95:2002—IEEE standard for radio-frequency energy and current flow symbols.

ISO 2315:1994—Two- and four-pole sealed electromagnetic relays, 2 A and 3 A—Clearance and fixing dimensions.

ISO 5066-1:1986—Hermetically sealed monostable electrical relays, 2 A and 3 A—Part 1: Operating characteristics and test conditions.

ISO 5066-2:1986—Hermetically sealed monostable electrical relays, 2 A and 3 A—Part 2: Type approval tests.

ISO 7637-1:2002—Road vehicles—Electrical disturbance by conduction and coupling—Part 1: Passenger cars and light commercial vehicles with nominal 12-V supply voltage—Electrical transient conduction along supply lines only.

ISO 7637-2:1990—Road vehicles—Electrical disturbance by conduction and coupling—Part 2: Commercial vehicles with nominal 24-V supply voltage—Electrical transient conduction along supply lines only.

ISO 7637-3:1995—Road vehicles—Electrical disturbance by conduction and coupling—Part 3: Vehicles with nominal 12-V or 24-V supply voltage—Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines.

ISO 11451-1:2001—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 1: General and definitions.

ISO 11451-2:2001—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 2: Off-vehicle radiation source.

ISO 11451-3:1994—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 3: On-board transmitter simulation.

ISO 11451-4:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 4: Bulk current injector (BCI).

ISO 11452-1:2001—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 1: General and definitions.

ISO 11452-2:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 2: Absorber-lined chamber.

ISO 11452-3:2001—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 3: Transverse electromagnetic mode (TEM) cell.

ISO 11452-4:2001—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 4: Bulk current injection (BCI).

ISO 11452-5:2002—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 5: Strip line.

ISO 11452-6:1997 (R1999)—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 6: Parallel plate antenna.

ISO 11452-7:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 7: Direct radio-frequency (RF) power injection.

ISO 13766:1999—Earth-moving machinery—Electromagnetic compatibility.

ISO 14982:1998—Agricultural and forestry machinery—Electromagnetic compatibility—Test methods and acceptance criteria.

ISO TR 10605:1994—Road vehicles—Electrical disturbances from electrostatic discharges.

ISO TR 11062:1994—Manipulating industrial robots—EMC test methods and performance evaluation criteria—Guidelines.

MIL-A-17161D:1985—Absorber, radio-frequency radiation (microwave-absorbing material), general specification for.

MIL-B-5087—Bonding, electrical, and lightning protection for aerospace systems.

MIL-E-6051E—Electromagnetic compatibility requirements, systems (aircraft and associated weapons systems).

MIL-HDBK-1512:1997—Electroexplosive subsystems, electrically initiated, design requirements, and test methods.

MIL-HDBK-1857:1998—Grounding, bonding, and shielding design practices.

MIL-HDBK-235/1B:2000—Electromagnetic (radiated) environment considerations for design and procurement of electrical and electronic equipment, subsystems, and systems.

MIL-HDBK-237B:1997—Electromagnetic environmental effects on platforms, systems, and equipment.

MIL-HDBK-241B—Design guide for EMI reduction in power supplies.

MIL-HDBK-274(1):1990—Electrical grounding for aircraft safety.

MIL-HDBK-293:1987—Electronic counter-countermeasures considerations in radar systems acquisition.

MIL-HDBK-294:1986—Electronic counter-countermeasures considerations in naval communication systems.

MIL-HDBK-335:1981 (R1992)—Management and design guidance, electromagnetic radiation hardness for air-launched ordnance systems.

MIL-HDBK-419A—Grounding, bonding, and shielding for electronic equipment and facilities.

MIL-HDBK-1857—Grounding, bonding, and shielding design practices.

MIL-STD-220B:2000—Method of insertion-loss measurement.

MIL-STD-285—Method of attenuation measure for enclosures; EM shielding for electronic test purposes.

MIL-STD-449D(1):1976—Measurement of radio-frequency spectrum characteristics.

MIL-STD-461E:1999—Requirements for the control of electromagnetic interference, characteristics of subsystems and equipment.

MIL-STD-463A—Definitions and systems of units, electromagnetic interference and electromagnetic compatibility.

MIL-STD-464A:2002—Electromagnetic environmental effects requirements for systems.

MIL-STD-469B:1996—Radar engineering interface requirements, electromagnetic compatibility metric.

MIL-STD-499D—Measurement of radio frequency spectrum characteristics.

MIL-STD-1310G:1996—Shipboard bonding, grounding, and other techniques for electromagnetic compatibility and safety.

MIL-STD-1377:1971—Effectiveness of cable, connector, and weapon enclosure shielding and filters in precluding hazards of electromagnetic radiation to ordnance, measurement of.

MIL-STD-1385B—General requirements for preclusion of ordnance hazards in EM fields.

MIL-STD-1512—Electroexplosive subsystems, electrically initiated, design requirements and test methods.

MIL-STD-1541A:1987—Electromagnetic compatibility requirements for space systems.

MIL-STD-1542A—EMC grounding requirements for space systems.

MIL-STD-1542B:1991—Electromagnetic compatibility and grounding requirements for space system facilities.

MIL-STD-1605:1973—Procedures for conducting a shipboard electromagnetic interference (EMI) survey (surface ships).

MIL-STD-1757A—Lightning protection of aerospace vehicles and hardware.

MIL-STD-1818A—Electromagnetic effects requirements for systems.

MIL-STD-1857—Grounding, bonding, and shielding design practices.

SAE ARP 936A:2003—Capacitor, 10 µF for EMI measurements.

SAE ARP 958D:2003—Electromagnetic interference measurement antennas—Standard calibration method.

SAE ARP 1172:1972 (R1991)—Filters, conventional, electromagnetic interference reduction, general specification.

SAE ARP 1173:1994—Test procedure to measure the RF shielding characteristics of EMI gaskets.

SAE ARP 1267:1973 (R1991)—Electromagnetic interference measurement impulse generators—Standard calibration requirements and techniques.

SAE ARP 1481A:1998—Corrosion control and electrical conductivity in enclosure design.

SAE ARP 1705:1981 (R1991)—Coaxial test procedure to measure the RF shielding characteristics of EMI gasket materials.

SAE ARP 1870:1987 (R1999)—Aerospace systems electrical bonding and grounding for electromagnetic compatibility and safety.

SAE ARP 1972:1994—Measurement practices and procedures recommended for EMC testing.

SAE ARP 4242:1999—Electromagnetic compatibility control requirements systems.

SAE ARP 4244:1998—Recommended insertion-loss test methods for EMI power-line filters.

SAE ARP 5412:1999—Aircraft lightning environment and related test waveforms.

SAE ARP 5413:1999—Certification of aircraft electrical/electronic systems for the indirect effects of lightning.

zhihongyang

内容非常详实!

zhaodl

很全面呀！！！！！
顶一下！ [s:9]