电磁兼容小小家

 找回密码
 注册
查看: 13628|回复: 15

QP定义

[复制链接]
发表于 2006-8-28 21:02:56 | 显示全部楼层 |阅读模式

老伙计,请登录,欢迎回家

您需要 登录 才可以下载或查看,没有帐号?注册

x
  Quasi-peak Measurements Quasi-peak detection is a form of detection where a signal level is weighted based on the repetition frequency of the spectral components making up the signal. That is to say; the result of a quasi-peak measurement depends on the repetition rate of the signal. Signals can be classified into two general categories based upon their repetition rate: narrowband or broadband. A narrowband signal is a signal that can be resolved by the spectrum analyzer. An example of a narrowband signal is a continuous wave (CW) signal. A CW signal is one signal at a fixed frequency. A broadband signal is a signal that cannot be resolved by the spectrum analyzer. An example of a broadband signal is a pulse signal. Peak, quasi-peak, and average detection will yield the same amplitude level for a narrowband signal. A broadband signal will yield a quasi-peak level lower than the peak level. The weighting (accounted for through specific charge and discharge time constants in the quasi-peak detector circuit), is a function of the repetition frequency of the signal being measured. The lower the repetition frequency, the lower the quasi-peak level. Many agencies governing the electromagnetic interference (EMI) from commercial products require quasi-peak detection to be used .Even if the emission from a device is over a test limit when measured with peak detection, the device will be considered to pass if the quasi-peak level is below the test limit. Because of the charge and discharge time constants used in the quasi-peak detector , the spectrum analyzer must sweep considerably slower when the quasi-peak detector is on. Since the quasi-peak level of a signal is always equal to or less than the peak level of that signal, quasi-peak detection need be employed only when a signal is close to or over the test limit when measured with peak detection. For initial measurements, peak detection is used since peak detection does not require the slower sweep times
 楼主| 发表于 2006-9-4 14:58:51 | 显示全部楼层
AV   PK的定义是现成的!

去下载区找一个关于这方面的技术资料!
发表于 2006-9-9 08:37:26 | 显示全部楼层
AV-QP-Peak的说明
我写了一个详细的分析的
小小家网友可以在下载栏目里找到
发表于 2007-2-3 14:08:13 | 显示全部楼层
看不下去阿 。。全是英文。。回头用中文好啊 ?谢谢!!!
[s:4]
发表于 2007-2-26 15:44:21 | 显示全部楼层
啊.....................
73CEBF73501AB10EA3E57A04A66B2849.GIF
发表于 2007-3-12 18:39:21 | 显示全部楼层
做了这么久的EMC ,现在才看到QP的定义,有点悲哀.要努力啊!!!
发表于 2007-4-12 18:04:15 | 显示全部楼层
大意知道了,只要用QP在頻譜儀中如何設置呢
发表于 2007-6-21 21:04:43 | 显示全部楼层
引用第12楼jqrt2007-04-12 18:04发表的“”:
大意知道了,只要用QP在頻譜儀中如何設置呢


可以在Detector中设置。
发表于 2007-9-27 03:44:46 | 显示全部楼层
窄带,宽带之区分主要是与中频相比较,中频就是:
30M~1G,120K
150K~30M,9K
150K之前,200Hz
发表于 2007-11-21 19:41:02 | 显示全部楼层
老兄,宽带和窄带是从频谱上相对于接收机的6dB中频带宽说的,脉冲的上升时间短决定了起具有较宽的频谱,连续波在频谱上就是1条线。
所以……

发表回复

您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|小黑屋|电磁兼容网 电磁兼容小小家 EMC工程师家园 电磁兼容(EMC)小小家学习园地

GMT+8, 2024-5-12 23:24 , Processed in 0.094400 second(s), 23 queries .

快速回复 返回顶部 返回列表